GFP88221

 

High Amp Facility Power Line Filters

 

GFP88221 4x600/800 Amp Power Line Filter Capacitive Input

GFP88231 4x600/800 Amp Power Line Filter Inductive Input 

100 dB @ 100 kHz ~ 18 GHz

Our high amp filter panels are an impressive 26 inches shorter and approximately 200 pounds lighter than before, with no reduction in performance or quality. 

EMI/RFI Facility Power Line Filters are used to block unwanted signals and remove interference from entering or exiting through your power lines.  Our High Amp Power Line Filters are specified to 60 dB @ 14 kHz.

The GFP88221 features 

  • A smaller build, to allow it to fit in most freight and commercial elevators.
  • Phase Filters from our GFP78XXX series to reduce the number of unique components.
  • A new design that can be used as a modular base for meeting higher amperage requirements.
  • Ability to configure multiple panels side by side on the same wall, different walls or back to back, if space is critical. 

Download Product Data Sheet:  GFP88221 GFP88231 Data Sheet

 

SPECIAL FEATURES

Filters:

Our Filters consist of Low Pass filter circuits, passive components which includes inductors, capacitors, resistors and optional transient suppression devices. Each Filter is manufactured and tested per applicable portions of MIL-PRF-15733. Filter cases 16 gage, CRS, painted finish, and sealed with welded and soldered seams for shielding effectiveness. Discharge resistors are incorporated to eliminate potential shock hazard

 

Enclosures: 

Our enclosures are Modified NEMA type fabricated panel of not less than 14 gauge cold rolled steel painted Gray (Std. Paint Color). They include an RF tight inner area secured with RF gasket for 100 dB minimum shielding effectiveness, 14 kHz to 18 GHz, minimum. Front cover allows access to filters and terminal standoffs, with Pre-wired standoffs, lugs and lifting ears included.

 

Custom Packaging:

To ensure your filters are received in the best condition possible, we customize our packaging by building our filters within a protective crate. We take extra care in packaging our filters to ensure our customers are satisfied with any product received from us. Our crates are heat treated to meet international shipping requirements. 

AVAILABLE OPTIONS
  • EMP and surge Suppressors
  • HUB and Fitting Installation
  • Legs are included (not optional)
  • Custom Paint Colors (Enclosure)
  • RF Secure Penetration Accessories
  • Voltage Indicator Lights
  • 400 Hz Filters (lower insertion loss performance
FUNCTIONAL CHARACTERISTICS
Voltage Ratings:
  • 24-1,000 VDC
  • 120/208 VAC (50/60 Hz)
  • 277/480 VAC (50/60 Hz)

Specifications

  • Voltage Drop: 2% maximum at full rated unity power factor load.
  • Harmonic Distortion: 4% maximum at full rated unity power factor load
  • Temperature Rating: MIL-PRF-15733
  • Current Overload: 140% maximum current rating
  • RF Radiation: Greater than 100 dB isolation
  • Dielectric With-Standing Voltage: 2,200 VDC (prior to installation of discharge resistors)
  • Insulation Resistance: MIL-PRF-15733 (prior to installation of discharge resistors)
  • Insertion loss:
    • 60 dB @ 14 KHz  
    • 100 dB @ 100 KHz to 18 GHz
    • 50/50 Ohm System
APPLICABLE SPECIFICATIONS
Military Specifications
  • MIL-PRF-15733 General
Military Test Methods
  • MIL-STD-202 Component Parts
  • MIL-STD-220 Insertion Loss
  • MIL-STD-285 Shielding Effectiveness
  • NFPA 70/2011 National Electrical Code Standards